• Remove as much of the stain as possible by blotting with white paper towels and scraping with a dull knife.
• Neutralize with an ammonia solution (1 tablespoon of clear household ammonia and 1/2 cup of water). Saturate spot with ammonia solution using spray bottle. Do not wet backing. Blot with a white paper towel to remove excess moisture.
• Apply a small quantity of detergent solution to the spot. (To make the detergent solution mix 1/4 teaspoon of a hand dish washing detergent which does not contain lanolin or bleach with 1 quart of water; examples of safe detergents are Dawn� and Joy�.) Use a blotting motion to work the detergent into the affected area. If spot is being removed continue applying detergent and blotting with a white paper towel until spot is removed.
• Rinse with tap water using a spray bottle, blot to remove excess moisture.
• Spray lightly with water, do not blot this time; apply pad of paper towels and brick and allow to dry.
• If there is still some stain on the carpet and blotting is not removing it, then moisten the tufts in the stained area with 3% hydrogen peroxide. Let stand for on (1) hour. Blot and repeat until carpet is stain free. Light will cause peroxide to change back to water so no rinsing is necessary. Apply pad of paper towels and weight down with brick.

Important – ALWAYS read and follow the care instructions and any warnings provided by the carpet or upholstery manufacturer. Carpeting and upholstery with natural fibers and/or certain dyes or finishes may require special treatment. If in doubt contact Clean As A Whistle for advice/service first. NEVER PROCEED with any stain removal instructions without knowing the exact nature of the stain involved. NEVER USE any retail products to remove stains from carpet or upholstery without seeking the advice of the manufacturer or you could void your warranty.

• Blot to remove excess liquid or stain.
• Wet fabric with minimum amount of water, soak 1 minute, and blot with paper towel. Repeat water/blot procedure until no stain is evident on towel, and then blot dry.
• If fabric stain is persistent, wet stained area with water. Apply small amount of detergent/water solution, work into stained area with sponge and blot. Repeat detergent/water application until no stain is evident on towel.
• Rinse with clear water to remove traces of detergent and blot dry. It is important to remove all traces of detergent to prevent rapid resoiling.
• Rinse with 3% acetic acid or 50/50 vinegar/water solution. Blot dry.

Important – ALWAYS read and follow the care instructions and any warnings provided by the carpet or upholstery manufacturer. Carpeting and upholstery with natural fibers and/or certain dyes or finishes may require special treatment. If in doubt contact Clean As A Whistle for advice/service first. NEVER PROCEED with any stain removal instructions without knowing the exact nature of the stain involved. NEVER USE any retail products to remove stains from carpet or upholstery without seeking the advice of the manufacturer or you could void your warranty.

• Remove as much of the stain as possible by using a spoon or dull knife. Blot up as much of the stain as possible with white paper towels.
• Neutralize by spraying the affected area with the ammonia solution (1 tablespoon of clear household ammonia and 1/2 cup of water). Care should be taken to remove all protein matter. Blot to remove excess moisture.
• Apply a small quantity of detergent solution to the spot. (To make the detergent solution mix 1/4 teaspoon of a hand dish washing detergent which does not contain lanolin or bleach with 1 quart of water; examples of safe detergents are Dawn� and Joy�.) Use a blotting motion to work the detergent into the affected area. If spot is being removed continue applying detergent and blotting with a white paper towel until spot is removed.
• Rinse with tap water using a spray bottle, blot to remove excess moisture.
• Spray lightly with water, do not blot this time; apply pad of paper towels and brick and allow to dry. If there is still some stain on the carpet and blotting is not removing it, then moisten the tufts in the stained area with 3% hydrogen peroxide. Let stand for on (1) hour. Blot and repeat until carpet is stain free. Light will cause peroxide to change back to water so no rinsing is necessary. Apply pad of paper towels and weight down with brick.

Important – ALWAYS read and follow the care instructions and any warnings provided by the carpet or upholstery manufacturer. Carpeting and upholstery with natural fibers and/or certain dyes or finishes may require special treatment. If in doubt contact Clean As A Whistle for advice/service first. NEVER PROCEED with any stain removal instructions without knowing the exact nature of the stain involved. NEVER USE any retail products to remove stains from carpet or upholstery without seeking the advice of the manufacturer or you could void your warranty.

• Remove as much of the stain as possible by using a spoon or dull knife. And, blot up as much of the stain as possible with white paper towels.
• Neutralize by spraying the affected area with the ammonia solution (1 tablespoon of clear household ammonia and 1/2 cup of water). Care should be taken to remove all protein matter. Blot to remove excess moisture.
• Apply a small quantity of detergent solution to the spot. (To make the detergent solution mix 1/4 teaspoon of a hand dish washing detergent which does not contain lanolin or bleach with 1 quart of water; examples of safe detergents are Dawn� and Joy�.) Use a blotting motion to work the detergent into the affected area. If spot is being removed continue applying detergent and blotting with a white paper towel until spot is removed.
• Rinse with tap water using a spray bottle, blot to remove excess moisture.
• Spray lightly with water, do not blot this time; apply pad of paper towels and brick and allow to dry.
• If there is still some stain on the carpet and blotting is not removing it, then moisten the tufts in the stained area with 3% hydrogen peroxide. Let stand for on (1) hour. Blot and repeat until carpet is stain free. Light will cause peroxide to change back to water so no rinsing is necessary. Apply pad of paper towels and weight down with brick.
• Use a blotting motion to work the detergent into the affected area. If spot is being removed continue applying detergent and blotting with a white paper towel until spot is removed.
• Rinse with tap water using a spray bottle, blot to remove excess moisture.
• Spray lightly with water, do not blot this time; apply pad of paper towels and brick and allow to dry.
• If there is still some stain on the carpet and blotting is not removing it, then moisten the tufts in the stained area with 3% hydrogen peroxide. Let stand for on (1) hour. Blot and repeat until carpet is stain free. Light will cause peroxide to change back to water so no rinsing is necessary. Apply pad of paper towels and weight down with brick.

Important – ALWAYS read and follow the care instructions and any warnings provided by the carpet or upholstery manufacturer. Carpeting and upholstery with natural fibers and/or certain dyes or finishes may require special treatment. If in doubt contact Clean As A Whistle for advice/service first. NEVER PROCEED with any stain removal instructions without knowing the exact nature of the stain involved. NEVER USE any retail products to remove stains from carpet or upholstery without seeking the advice of the manufacturer or you could void your warranty.

• Remove as much of the stain as possible by blotting with a white paper towel or scraping with a dull knife.
• Neutralize with an ammonia solution (1 tablespoon of clear household ammonia and 1/2 cup of water). Saturate spot with ammonia solution using spray bottle. Do not wet backing. Blot with a white paper towel to remove excess moisture.
• Apply a small quantity of detergent solution to the spot. (To make the detergent solution mix 1/4 teaspoon of a hand dish washing detergent which does not contain lanolin or bleach with 1 quart of water; examples of safe detergents are Dawn� and Joy�.) Use a blotting motion to work the detergent into the affected area. If spot is being removed continue applying detergent and blotting with a white paper towel until spot is removed.
• Rinse with tap water using a spray bottle, blot to remove excess moisture.
• Spray lightly with water, do not blot this time; apply pad of paper towels and brick and allow to dry.
• If there is still some stain on the carpet and blotting is not removing it, then moisten the tufts in the stained area with 3% hydrogen peroxide. Let stand for on (1) hour. Blot and repeat until carpet is stain free. Light will cause peroxide to change back to water so no rinsing is necessary. Apply pad of paper towels and weight down with brick.

Important – ALWAYS read and follow the care instructions and any warnings provided by the carpet or upholstery manufacturer. Carpeting and upholstery with natural fibers and/or certain dyes or finishes may require special treatment. If in doubt contact Clean As A Whistle for advice/service first. NEVER PROCEED with any stain removal instructions without knowing the exact nature of the stain involved. NEVER USE any retail products to remove stains from carpet or upholstery without seeking the advice of the manufacturer or you could void your warranty.

• Blot with a white paper towel to remove as much of the stain as possible.
• Neutralize with the white vinegar solution (1/3 cup WHIE vinegar and 2/3 cup of water). Saturate spot with the white vinegar solution, using a spray bottle and blot to remove excess moisture.
• Apply a small quantity of detergent solution to the spot. (To make the detergent solution mix 1/4 teaspoon of a hand dish washing detergent which does not contain lanolin or bleach with 1 quart of water; examples of safe detergents are Dawn� and Joy�.) Use a blotting motion to work the detergent into the affected area. If spot is being removed continue applying detergent and blotting with a white paper towel until spot is removed.
• Rinse with tap water using a spray bottle, blot to remove excess moisture.
• Spray lightly with water, do not blot this time; apply pad of paper towels and brick and allow to dry.
• If there is still some stain on the carpet and blotting is not removing it, then moisten the tufts in the stained area with 3% hydrogen peroxide. Let stand for on (1) hour. Blot and repeat until carpet is stain free. Light will cause peroxide to change back to water so no rinsing is necessary. Apply pad of paper towels and weight down with brick.

Important – ALWAYS read and follow the care instructions and any warnings provided by the carpet or upholstery manufacturer. Carpeting and upholstery with natural fibers and/or certain dyes or finishes may require special treatment. If in doubt contact Clean As A Whistle for advice/service first. NEVER PROCEED with any stain removal instructions without knowing the exact nature of the stain involved. NEVER USE any retail products to remove stains from carpet or upholstery without seeking the advice of the manufacturer or you could void your warranty.

• Remove as much of the tar as possible by blotting with a white paper towel or scraping with a dull knife.
• Apply isopropyl rubbing alcohol to a clean white cloth, white paper towel or cotton ball. If the spot extends deep into the pile use a blotting motion until the spot is removed or no color is transferred to the cloth. Do not allow the alcohol to penetrate into the backing as this will destroy the latex bond. If the spot is on the surface only, rub in one direction at a time. Never us a circular motion to remove spot as this may destroy the texture. Stop if spot is removed. If not, go to the next step.
• Apply a small quantity of detergent solution to the spot. (To make the detergent solution mix 1/4 teaspoon of a hand dish washing detergent which does not contain lanolin or bleach with 1 quart of water; examples of safe detergents are Dawn� and Joy�.) Use a blotting motion to work the detergent into the affected area. If spot is being removed continue applying detergent and blotting with a white paper towel until spot is removed.
• Rinse with tap water using a spray bottle, blot to remove excess moisture, spray lightly with water, do not blot this time; apply pad of paper towels and brick and allow to dry.
• If there is still some stain on the carpet and blotting is not removing it, then moisten the tufts in the stained area with 3% hydrogen peroxide. Let stand for on (1) hour. Blot and repeat until carpet is stain free. Light will cause peroxide to change back to water so no rinsing is necessary. Apply pad of paper towels and weight down with brick.

Important – ALWAYS read and follow the care instructions and any warnings provided by the carpet or upholstery manufacturer. Carpeting and upholstery with natural fibers and/or certain dyes or finishes may require special treatment. If in doubt contact Clean As A Whistle for advice/service first. NEVER PROCEED with any stain removal instructions without knowing the exact nature of the stain involved. NEVER USE any retail products to remove stains from carpet or upholstery without seeking the advice of the manufacturer or you could void your warranty.

• Remove as much of the foreign material as possible by blotting with a white paper towel or scraping with a dull knife.
• Apply isopropyl rubbing alcohol to a clean white cloth, white paper towel or cotton ball. If the spot extends deep into the pile use a blotting motion until the spot is removed or no color is transferred to the cloth. Do not allow the alcohol to penetrate into the backing as this will destroy the latex bond. If the spot is on the surface only, rub in one direction at a time. Never us a circular motion to remove spot as this may destroy the texture. Stop if spot is removed. If not, go to the next step.
• Apply a small quantity of detergent solution to the spot. (To make the detergent solution mix 1/4 teaspoon of a hand dish washing detergent which does not contain lanolin or bleach with 1 quart of water; examples of safe detergents are Dawn� and Joy�.) Use a blotting motion to work the detergent into the affected area. If spot is being removed continue applying detergent and blotting with a white paper towel until spot is removed.
• Rinse with tap water using a spray bottle, blot to remove excess moisture.
• Spray lightly with water, do not blot this time; apply pad of paper towels and brick and allow to dry.
• If there is still some stain on the carpet and blotting is not removing it, then moisten the tufts in the stained area with 3% hydrogen peroxide. Let stand for on (1) hour. Blot and repeat until carpet is stain free. Light will cause peroxide to change back to water so no rinsing is necessary. Apply pad of paper towels and weight down with brick.

Important – ALWAYS read and follow the care instructions and any warnings provided by the carpet or upholstery manufacturer. Carpeting and upholstery with natural fibers and/or certain dyes or finishes may require special treatment. If in doubt contact Clean As A Whistle for advice/service first. NEVER PROCEED with any stain removal instructions without knowing the exact nature of the stain involved. NEVER USE any retail products to remove stains from carpet or upholstery without seeking the advice of the manufacturer or you could void your warranty.

• Vacuum, using crevice tool of vacuum cleaner to remove the soot. If all, or most, of the soot has not been removed, call a professional cleaner. If vacuuming has removed all particles go to the next step
• Remove as much of the foreign material as possible by blotting with a white paper towel or scraping with a dull knife.
• Apply isopropyl rubbing alcohol to a clean white cloth, white paper towel or cotton ball. If the spot extends deep into the pile use a blotting motion until the spot is removed or no color is transferred to the cloth. Do not allow the alcohol to penetrate into the backing as this will destroy the latex bond. If the spot is on the surface only, rub in one direction at a time. Never us a circular motion to remove spot as this may destroy the texture. Stop if spot is removed. If not, go to the next step.
• Apply a small quantity of detergent solution to the spot. (To make the detergent solution mix 1/4 teaspoon of a hand dish washing detergent which does not contain lanolin or bleach with 1 quart of water; examples of safe detergents are Dawn� and Joy�.) Use a blotting motion to work the detergent into the affected area. If spot is being removed continue applying detergent and blotting with a white paper towel until spot is removed.
• Rinse with tap water using a spray bottle, blot to remove excess moisture.
• Spray lightly with water, do not blot this time; apply pad of paper towels and brick and allow to dry.
• If there is still some stain on the carpet and blotting is not removing it, then moisten the tufts in the stained area with 3% hydrogen peroxide. Let stand for on (1) hour. Blot and repeat until carpet is stain free. Light will cause peroxide to change back to water so no rinsing is necessary. Apply pad of paper towels and weight down with brick.

Important – ALWAYS read and follow the care instructions and any warnings provided by the carpet or upholstery manufacturer. Carpeting and upholstery with natural fibers and/or certain dyes or finishes may require special treatment. If in doubt contact Clean As A Whistle for advice/service first. NEVER PROCEED with any stain removal instructions without knowing the exact nature of the stain involved. NEVER USE any retail products to remove stains from carpet or upholstery without seeking the advice of the manufacturer or you could void your warranty.

• Blot with white paper towel to remove as much of the stain as possible then neutralize with an ammonia solution (1 tablespoon of clear household ammonia and 1/2 cup of water). Saturate spot with the ammonia solution using spray bottle. Do not wet backing. Blot with a white paper towel to remove excess moisture.
• Apply a small quantity of detergent solution to the spot. (To make the detergent solution mix 1/4 teaspoon of a hand dish washing detergent which does not contain lanolin or bleach with 1 quart of water; examples of safe detergents are Dawn� and Joy�.) Use a blotting motion to work the detergent into the affected area. If spot is being removed continue applying detergent and blotting with a white paper towel until spot is removed.
• Rinse with tap water using a spray bottle, blot to remove excess moisture.
• Spray lightly with water, do not blot this time; apply pad of paper towels and brick and allow to dry.
• If there is still some stain on the carpet and blotting is not removing it, then moisten the tufts in the stained area with 3% hydrogen peroxide. Let stand for on (1) hour. Blot and repeat until carpet is stain free. Light will cause peroxide to change back to water so no rinsing is necessary. Apply pad of paper towels and weight down with brick.

Important – ALWAYS read and follow the care instructions and any warnings provided by the carpet or upholstery manufacturer. Carpeting and upholstery with natural fibers and/or certain dyes or finishes may require special treatment. If in doubt contact Clean As A Whistle for advice/service first. NEVER PROCEED with any stain removal instructions without knowing the exact nature of the stain involved. NEVER USE any retail products to remove stains from carpet or upholstery without seeking the advice of the manufacturer or you could void your warranty.